diff options
| -rw-r--r-- | keyboards/jd40/Makefile | 73 | 
1 files changed, 1 insertions, 72 deletions
| diff --git a/keyboards/jd40/Makefile b/keyboards/jd40/Makefile index 242748111c..57b2ef62e5 100644 --- a/keyboards/jd40/Makefile +++ b/keyboards/jd40/Makefile @@ -1,74 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -#     This will define a symbol, F_CPU, in all source code files equal to the -#     processor frequency in Hz. You can then use this symbol in your source code to -#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done -#     automatically to create a 32-bit value in your source code. -# -#     This will be an integer division of F_USB below, as it is sourced by -#     F_USB after it has run through any CPU prescalers. Note that this value -#     does not *change* the processor frequency - it should merely be updated to -#     reflect the processor speed set externally so that the code can use accurate -#     software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -#     This will define a symbol, F_USB, in all source code files equal to the -#     input clock frequency (before any prescaling is performed) in Hz. This value may -#     differ from F_CPU if prescaling is used on the latter, and is required as the -#     raw input clock is fed directly to the PLL sections of the AVR for high speed -#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -#     at the end, this will be done automatically to create a 32-bit value in your -#     source code. -# -#     If no clock division is performed on the input clock inside the AVR (via the -#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -#   Teensy halfKay   512 -#   Teensy++ halfKay 1024 -#   Atmel DFU loader 4096 -#   LUFA bootloader  4096 -#   USBaspLoader     2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -#   comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes		# Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes		# Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes		# Audio control and System control(+450) -# CONSOLE_ENABLE ?= yes		# Console for debug(+400) -# COMMAND_ENABLE ?= yes		# Commands for debug and configuration -KEYBOARD_LOCK_ENABLE ?= yes	# Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE ?= yes	# Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes			# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE ?= yes	# Enable keyboard backlight functionality -# MIDI_ENABLE ?= YES			# MIDI controls -# UNICODE_ENABLE ?= YES		# Unicode -# BLUETOOTH_ENABLE ?= yes	# Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE ?= yes          # Enable RGB Underglow - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED  	include ../../Makefile  endif - | 
