diff options
| -rw-r--r-- | keyboards/kitten_paw/Makefile | 77 | ||||
| -rw-r--r-- | keyboards/kitten_paw/config.h | 162 | ||||
| -rw-r--r-- | keyboards/kitten_paw/keymaps/default/keymap.c | 51 | ||||
| -rw-r--r-- | keyboards/kitten_paw/kitten_paw.c | 30 | ||||
| -rw-r--r-- | keyboards/kitten_paw/kitten_paw.h | 47 | ||||
| -rw-r--r-- | keyboards/kitten_paw/led.c | 47 | ||||
| -rw-r--r-- | keyboards/kitten_paw/matrix.c | 164 | ||||
| -rw-r--r-- | keyboards/kitten_paw/readme.md | 32 | ||||
| -rw-r--r-- | keyboards/readme.md | 1 | 
9 files changed, 611 insertions, 0 deletions
| diff --git a/keyboards/kitten_paw/Makefile b/keyboards/kitten_paw/Makefile new file mode 100644 index 0000000000..9122921737 --- /dev/null +++ b/keyboards/kitten_paw/Makefile @@ -0,0 +1,77 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u2 + +# Processor frequency. +#     This will define a symbol, F_CPU, in all source code files equal to the +#     processor frequency in Hz. You can then use this symbol in your source code to +#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done +#     automatically to create a 32-bit value in your source code. +# +#     This will be an integer division of F_USB below, as it is sourced by +#     F_USB after it has run through any CPU prescalers. Note that this value +#     does not *change* the processor frequency - it should merely be updated to +#     reflect the processor speed set externally so that the code can use accurate +#     software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +#     This will define a symbol, F_USB, in all source code files equal to the +#     input clock frequency (before any prescaling is performed) in Hz. This value may +#     differ from F_CPU if prescaling is used on the latter, and is required as the +#     raw input clock is fed directly to the PLL sections of the AVR for high speed +#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +#     at the end, this will be done automatically to create a 32-bit value in your +#     source code. +# +#     If no clock division is performed on the input clock inside the AVR (via the +#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +#   Teensy halfKay   512 +#   Teensy++ halfKay 1024 +#   Atmel DFU loader 4096 +#   LUFA bootloader  4096 +#   USBaspLoader     2048 +	OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +#   change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes        # Console for debug(+400) +COMMAND_ENABLE ?= yes        # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no            # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no            # MIDI controls +UNICODE_ENABLE ?= no         # Unicode +BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no           # Audio output on port C6 + +CUSTOM_MATRIX = yes +SRC += matrix.c led.c + +ifndef QUANTUM_DIR +	include ../../Makefile +endif + diff --git a/keyboards/kitten_paw/config.h b/keyboards/kitten_paw/config.h new file mode 100644 index 0000000000..d7089734aa --- /dev/null +++ b/keyboards/kitten_paw/config.h @@ -0,0 +1,162 @@ +/* +Copyright 2012 Jun Wako <[email protected]> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program.  If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + + +/* USB Device descriptor parameter */ +#define VENDOR_ID       0xFEED +#define PRODUCT_ID      0x6050 +#define DEVICE_VER      0x0104 +#define MANUFACTURER    Costar +#define PRODUCT         Majestouch + +/* key matrix size */ +#define MATRIX_ROWS 8 +#define MATRIX_COLS 18 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +//#define MATRIX_ROW_PINS { D0, D5 } +//#define MATRIX_COL_PINS { F1, F0, B0 } +//#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW +  +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ +    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1          H +//#define MAGIC_KEY_HELP2          SLASH +//#define MAGIC_KEY_DEBUG          D +//#define MAGIC_KEY_DEBUG_MATRIX   X +//#define MAGIC_KEY_DEBUG_KBD      K +//#define MAGIC_KEY_DEBUG_MOUSE    M +//#define MAGIC_KEY_VERSION        V +//#define MAGIC_KEY_STATUS         S +//#define MAGIC_KEY_CONSOLE        C +//#define MAGIC_KEY_LAYER0_ALT1    ESC +//#define MAGIC_KEY_LAYER0_ALT2    GRAVE +//#define MAGIC_KEY_LAYER0         0 +//#define MAGIC_KEY_LAYER1         1 +//#define MAGIC_KEY_LAYER2         2 +//#define MAGIC_KEY_LAYER3         3 +//#define MAGIC_KEY_LAYER4         4 +//#define MAGIC_KEY_LAYER5         5 +//#define MAGIC_KEY_LAYER6         6 +//#define MAGIC_KEY_LAYER7         7 +//#define MAGIC_KEY_LAYER8         8 +//#define MAGIC_KEY_LAYER9         9 +//#define MAGIC_KEY_BOOTLOADER     PAUSE +//#define MAGIC_KEY_LOCK           CAPS +//#define MAGIC_KEY_EEPROM         E +//#define MAGIC_KEY_NKRO           N +//#define MAGIC_KEY_SLEEP_LED      Z + +/* + * Feature disable options + *  These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/kitten_paw/keymaps/default/keymap.c b/keyboards/kitten_paw/keymaps/default/keymap.c new file mode 100644 index 0000000000..f672357455 --- /dev/null +++ b/keyboards/kitten_paw/keymaps/default/keymap.c @@ -0,0 +1,51 @@ +#include "kitten_paw.h" + +enum layers { +    DEFAULT, +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +  [DEFAULT] = KEYMAP(\ +       KC_ESC,  KC_F1,  KC_F2,  KC_F3,  KC_F4,  KC_F5,  KC_F6,  KC_F7,  KC_F8,  KC_F9, KC_F10, KC_F11, KC_F12,          KC_PSCR,KC_SLCK,KC_PAUS,                        \ +       KC_GRV,   KC_1,   KC_2,   KC_3,   KC_4,   KC_5,   KC_6,   KC_7,   KC_8,   KC_9,   KC_0,KC_MINS, KC_EQL,KC_BSPC,   KC_INS,KC_HOME,KC_PGUP,  KC_NLCK,KC_PSLS,KC_PAST,KC_PMNS, \ +       KC_TAB,   KC_Q,   KC_W,   KC_E,   KC_R,   KC_T,   KC_Y,   KC_U,   KC_I,   KC_O,   KC_P,KC_LBRC,KC_RBRC,KC_BSLS,   KC_DEL, KC_END,KC_PGDN,    KC_P7,  KC_P8,  KC_P9,KC_PPLS, \ +      KC_CAPS,   KC_A,   KC_S,   KC_D,   KC_F,   KC_G,   KC_H,   KC_J,   KC_K,   KC_L,KC_SCLN,KC_QUOT,         KC_ENT,                              KC_P4,  KC_P5,  KC_P6,      \ +      KC_LSFT,KC_NUBS,   KC_Z,   KC_X,   KC_C,   KC_V,   KC_B,   KC_N,   KC_M,KC_COMM, KC_DOT,KC_SLSH,        KC_RSFT,            KC_UP,            KC_P1,  KC_P2,  KC_P3,KC_PENT, \ +      KC_LCTL,KC_LGUI,KC_LALT,                 KC_SPC,                                KC_RALT,KC_RGUI,KC_MENU,KC_RCTL,  KC_LEFT,KC_DOWN,KC_RGHT,    KC_P0,KC_PDOT) +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ +  // MACRODOWN only works in this function +      switch(id) { +        case 0: +          if (record->event.pressed) { +            register_code(KC_RSFT); +          } else { +            unregister_code(KC_RSFT); +          } +        break; +      } +    return MACRO_NONE; +}; + + +void matrix_init_user(void) { + +} + +void matrix_scan_user(void) { + +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { +  return true; +} + +void led_set_user(uint8_t usb_led) { + +}
\ No newline at end of file diff --git a/keyboards/kitten_paw/kitten_paw.c b/keyboards/kitten_paw/kitten_paw.c new file mode 100644 index 0000000000..8713baf433 --- /dev/null +++ b/keyboards/kitten_paw/kitten_paw.c @@ -0,0 +1,30 @@ +#include "kitten_paw.h" + +void matrix_init_kb(void) { +	// put your keyboard start-up code here +	// runs once when the firmware starts up + +    matrix_init_quantum(); +	matrix_init_user(); +} + +void matrix_scan_kb(void) { +	// put your looping keyboard code here +	// runs every cycle (a lot) + +    matrix_scan_quantum(); +    matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { +	// put your per-action keyboard code here +	// runs for every action, just before processing by the firmware + +	return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { +	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + +	led_set_user(usb_led); +} diff --git a/keyboards/kitten_paw/kitten_paw.h b/keyboards/kitten_paw/kitten_paw.h new file mode 100644 index 0000000000..a6c1d27de7 --- /dev/null +++ b/keyboards/kitten_paw/kitten_paw.h @@ -0,0 +1,47 @@ +#ifndef KITTEN_PAW_H +#define KITTEN_PAW_H + +#include "quantum.h" + +// This a shortcut to help you visually see your layout. +// The first section contains all of the arguements +// The second converts the arguments into a two-dimensional array +/* +  Matrix col/row mapping +   +  ,----.    ,-------------------. ,-------------------. ,-------------------. ,--------------. +  | J6 |    | I4 | H4 | H2 | H6 | | A7 | E6 | D2 | D4 | | B4 | B7 | B6 | B0 | | C7 | C5 | A5 | +  `----'    `-------------------' `-------------------' `-------------------' `--------------' +  ,-------------------------------------------------------------------------. ,--------------. ,-------------------. +  | J4 | J7 | I7 | H7 | G7 | G4 | F4 | F7 | E7 | D7 | R7 | R4 | E4 |     B2 | | L4 | O4 | Q4 | | K1 | L1 | Q1 | Q0 | +  |-------------------------------------------------------------------------| |--------------| |-------------------| +  | J2   | J5 | I5 | H5 | G5 | G2 | F2 | F5 | E5 | D5 | R5 | R2 | E2 |   B3 | | K4 | O7 | Q7 | | K5 | L5 | Q5 | O5 | +  |-------------------------------------------------------------------------| '--------------' |--------------     | +  | O5    | J3 | I3 | H3 | G3 | G6 | F6 | F3 | E3 | D3 | R3 | R6 |       B1 |                  | K2 | L2 | Q2 |    | +  |-------------------------------------------------------------------------|      ,----.      |-------------------| +  | N2      | J1 | I1 | H1 | G1 | G0 | F0 | F1 | E1 | D1 | R0 |          N3 |      | O6 |      | K3 | L3 | Q3 | O3 | +  |-------------------------------------------------------------------------| ,--------------. |--------------     | +  | A4 | P2 | C6 |                  K6                  | C0 | M3 | D0 | A1 | | O0 | K0 | L0 | | L6      | Q6 |    | +  `-------------------------------------------------------------------------' `--------------' `-------------------' +*/ + +#define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{ \ +    {KC_NO,  KB0,  KC0,  KD0,KC_NO,  KF0,  KG0,KC_NO,KC_NO,KC_NO,  KK0,  KL0,KC_NO,KC_NO,  KO0,KC_NO,  KQ0,  KR0}, \ +    {  KA1,  KB1,KC_NO,  KD1,  KE1,  KF1,  KG1,  KH1,  KI1,  KJ1,  KK1,  KL1,KC_NO,KC_NO,KC_NO,KC_NO,  KQ1,KC_NO}, \ +    {KC_NO,  KB2,KC_NO,  KD2,  KE2,  KF2,  KG2,  KH2,  KI2,  KJ2,  KK2,  KL2,KC_NO,  KN2,KC_NO,  KP2,  KQ2,  KR2}, \ +    {KC_NO,  KB3,KC_NO,  KD3,  KE3,  KF3,  KG3,  KH3,  KI3,  KJ3,  KK3,  KL3,  KM3,  KN3,  KO3,KC_NO,  KQ3,  KR3}, \ +    {  KA4,  KB4,KC_NO,  KD4,  KE4,  KF4,  KG4,  KH4,  KI4,  KJ4,  KK4,  KL4,KC_NO,KC_NO,  KO4,KC_NO,  KQ4,  KR4}, \ +    {  KA5,KC_NO,  KC5,  KD5,  KE5,  KF5,  KG5,  KH5,  KI5,  KJ5,  KK5,  KL5,KC_NO,KC_NO,  KO5,KC_NO,  KQ5,  KR5}, \ +    {KC_NO,  KB6,  KC6,KC_NO,  KE6,  KF6,  KG6,  KH6,  KI6,  KJ6,  KK6,  KL6,KC_NO,KC_NO,  KO6,KC_NO,  KQ6,  KR6}, \ +    {  KA7,  KB7,  KC7,  KD7,  KE7,  KF7,  KG7,  KH7,  KI7,  KJ7,KC_NO,KC_NO,KC_NO,KC_NO,  KO7,KC_NO,  KQ7,  KR7} \ +} + +#endif diff --git a/keyboards/kitten_paw/led.c b/keyboards/kitten_paw/led.c new file mode 100644 index 0000000000..a1bf057c4c --- /dev/null +++ b/keyboards/kitten_paw/led.c @@ -0,0 +1,47 @@ +/* +  Copyright 2014 Ralf Schmitt <[email protected]> + +  This program is free software: you can redistribute it and/or modify +  it under the terms of the GNU General Public License as published by +  the Free Software Foundation, either version 2 of the License, or +  (at your option) any later version. + +  This program is distributed in the hope that it will be useful, +  but WITHOUT ANY WARRANTY; without even the implied warranty of +  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the +  GNU General Public License for more details. + +  You should have received a copy of the GNU General Public License +  along with this program.  If not, see <http://www.gnu.org/licenses/>. +*/ + +#include <avr/io.h> +#include "stdint.h" +#include "led.h" + +/* LED pin configuration + * + * Scroll Lock  PC5 + * Caps Lock    PC6 + * Num Lock     PB7 + * + */ +void led_set(uint8_t usb_led) { +  DDRB |= (1<<7); +  DDRC |= (1<<5) | (1<<6); +   +  if (usb_led & (1<<USB_LED_CAPS_LOCK)) +    PORTC &= ~(1<<6); +  else +    PORTC |=  (1<<6); +   +  if (usb_led & (1<<USB_LED_NUM_LOCK)) +    PORTB &= ~(1<<7); +  else +    PORTB |=  (1<<7); +   +  if (usb_led & (1<<USB_LED_SCROLL_LOCK)) +    PORTC &= ~(1<<5); +  else +    PORTC |=  (1<<5); +} diff --git a/keyboards/kitten_paw/matrix.c b/keyboards/kitten_paw/matrix.c new file mode 100644 index 0000000000..46875293fc --- /dev/null +++ b/keyboards/kitten_paw/matrix.c @@ -0,0 +1,164 @@ +/* +  Copyright 2014 Ralf Schmitt <[email protected]> + +  This program is free software: you can redistribute it and/or modify +  it under the terms of the GNU General Public License as published by +  the Free Software Foundation, either version 2 of the License, or +  (at your option) any later version. + +  This program is distributed in the hope that it will be useful, +  but WITHOUT ANY WARRANTY; without even the implied warranty of +  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the +  GNU General Public License for more details. + +  You should have received a copy of the GNU General Public License +  along with this program.  If not, see <http://www.gnu.org/licenses/>. +*/ + +#include <stdint.h> +#include <stdbool.h> +#include <avr/io.h> +#include <util/delay.h> +#include "print.h" +#include "debug.h" +#include "util.h" +#include "matrix.h" + +#ifndef DEBOUNCING_DELAY +#   define DEBOUNCING_DELAY 5 +#endif +static uint8_t debouncing = DEBOUNCING_DELAY; + +static matrix_row_t matrix[MATRIX_ROWS]; +static matrix_row_t matrix_debouncing[MATRIX_ROWS]; + +static uint8_t read_rows(void); +static void select_col(uint8_t col); + +inline uint8_t matrix_rows(void) { +  return MATRIX_ROWS; +} + +inline uint8_t matrix_cols(void) { +  return MATRIX_COLS; +} + +/* Column pin configuration + * + * col: 0    1    2    3    4    5    6    7 + * pin: PC7  PD5  PD3  PD1  PC2  PD6  PD4  PD2 + * + * Rrr pin configuration  + * + * These rrrs uses one 74HC154 4 to 16 bit demultiplexer (low + * active), together with 2 rrrs driven directly from the micro + * controller, to control the 18 rrrs. The rrrs are driven from + * pins B6,5,4,3,2,1,0. + */ +void matrix_init(void) { +  DDRC  &= ~0b10000100;  // Row input pins +  DDRD  &= ~0b01111110; +  PORTC |=  0b10000100; +  PORTD |=  0b01111110; + +  DDRB  |=  0b01111111;  // Column output pins + +  for (uint8_t i=0; i < MATRIX_ROWS; i++)  { +    matrix[i] = 0; +    matrix_debouncing[i] = 0; +  } +} + +uint8_t matrix_scan(void) { +  for (uint8_t col = 0; col < MATRIX_COLS; col++) { +    select_col(col); +    _delay_us(3); +    uint8_t rows = read_rows(); +    for (uint8_t row = 0; row < MATRIX_ROWS; row++) { +      bool prev_bit = matrix_debouncing[row] & ((matrix_row_t)1<<col); +      bool curr_bit = rows & (1<<row); +      if (prev_bit != curr_bit) { +        matrix_debouncing[row] ^= ((matrix_row_t)1<<col); +        debouncing = DEBOUNCING_DELAY; +      } +    } +  } +   +  if (debouncing) { +    if (--debouncing) { +      _delay_ms(1); +    } +    else { +      for (uint8_t i = 0; i < MATRIX_ROWS; i++) { +        matrix[i] = matrix_debouncing[i]; +      } +    } +  } +   +  return 1; +} + +bool matrix_is_modified(void) { +  if (debouncing) +    return false; +  else +    return true; +} + +inline bool matrix_is_on(uint8_t row, uint8_t col) { +  return (matrix[row] & ((matrix_row_t)1<<col)); +} + +inline matrix_row_t matrix_get_row(uint8_t row) { +  return matrix[row]; +} + +void matrix_print(void) { +  print("\nr/c 0123456789ABCDEF\n"); +  for (uint8_t row = 0; row < MATRIX_ROWS; row++) { +    xprintf("%02X: %032lb\n", row, bitrev32(matrix_get_row(row))); +  } +} + +uint8_t matrix_key_count(void) { +  uint8_t count = 0; +  for (uint8_t i = 0; i < MATRIX_ROWS; i++) { +    count += bitpop32(matrix[i]); +  } +  return count; +} + +static uint8_t read_rows(void) { +  return +    (PINC&(1<<7) ? 0 : (1<<0)) | +    (PIND&(1<<5) ? 0 : (1<<1)) | +    (PIND&(1<<3) ? 0 : (1<<2)) | +    (PIND&(1<<1) ? 0 : (1<<3)) | +    (PINC&(1<<2) ? 0 : (1<<4)) | +    (PIND&(1<<2) ? 0 : (1<<5)) | +    (PIND&(1<<4) ? 0 : (1<<6)) | +    (PIND&(1<<6) ? 0 : (1<<7)); +} + +static void select_col(uint8_t col) { +  switch (col) { +  case  0: PORTB = (PORTB & ~0b01111111) | 0b01100100; break; +  case  1: PORTB = (PORTB & ~0b01111111) | 0b01101100; break; +  case  2: PORTB = (PORTB & ~0b01111111) | 0b01100010; break; +  case  3: PORTB = (PORTB & ~0b01111111) | 0b01111010; break; +  case  4: PORTB = (PORTB & ~0b01111111) | 0b01100110; break; +  case  5: PORTB = (PORTB & ~0b01111111) | 0b01110110; break; +  case  6: PORTB = (PORTB & ~0b01111111) | 0b01101110; break; +  case  7: PORTB = (PORTB & ~0b01111111) | 0b01111110; break; +  case  8: PORTB = (PORTB & ~0b01111111) | 0b01000001; break; +  case  9: PORTB = (PORTB & ~0b01111111) | 0b00100001; break; +  case 10: PORTB = (PORTB & ~0b01111111) | 0b01101010; break; +  case 11: PORTB = (PORTB & ~0b01111111) | 0b01110010; break; +  case 12: PORTB = (PORTB & ~0b01111111) | 0b01111100; break; +  case 13: PORTB = (PORTB & ~0b01111111) | 0b01110100; break; +  case 14: PORTB = (PORTB & ~0b01111111) | 0b01111000; break; +  case 15: PORTB = (PORTB & ~0b01111111) | 0b01110000; break; +  case 16: PORTB = (PORTB & ~0b01111111) | 0b01100000; break; +  case 17: PORTB = (PORTB & ~0b01111111) | 0b01101000; break; +  } +} diff --git a/keyboards/kitten_paw/readme.md b/keyboards/kitten_paw/readme.md new file mode 100644 index 0000000000..a6ef2a0672 --- /dev/null +++ b/keyboards/kitten_paw/readme.md @@ -0,0 +1,32 @@ +kitten_paw keyboard firmware +====================== +This is the firmware for the 2016 revision of the Kitten Paw controller by Bathroom Epiphanies. +Most of the boilerplate code is the work of [BathroomEpiphanies](https://github.com/BathroomEpiphanies). + +NKRO doesn't work at the moment, I don't know if I will take the time to find out how to fix this, so far 6KRO is enough for me. + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/doc/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/kitten_paw folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file.  + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default + +To build with the default keymap, simply run `make`. + +### Other Keymaps + +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `keymap` option like: + +``` +$ make keymap=[default|jack|<name>] +``` + +Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/` diff --git a/keyboards/readme.md b/keyboards/readme.md index f6c90b1f63..4f17962191 100644 --- a/keyboards/readme.md +++ b/keyboards/readme.md @@ -39,6 +39,7 @@ These keyboards are part of the QMK repository, but their manufacturers are not  * [hhkb](/keyboards/hhkb) — The Happy Hacking keyboard can be hacked with a custom controller to run QMK.  * [jd45](/keyboards/jd45) — Another Geekhack community project, designed by jdcarpe.  * [kc60](/keyboards/kc60) — A programmable Chinese-made keyboard, lost in the mists of time. +* [kitten_paw](/keyboards/kitten_paw) — A replacement controller (2016 revision) for the Filco Majestouch by [Bathroom Epiphanies](https://github.com/BathroomEpiphanies)  * [phantom](/keyboards/phantom) — A tenkeyless kit by Teel, also from Geekhack.  * [retro_refit](/keyboards/retro_refit) — Another creation by IBNobody.  * [satan](/keyboards/satan) — A GH60 variant. | 
