diff options
| -rw-r--r-- | keyboards/handwired/traveller/Makefile | 89 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/config.h | 173 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/keymaps/default/keymap.c | 305 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/keymaps/default/readme.md | 2 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/readme.md | 35 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/traveller.c | 61 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/traveller.h | 32 | 
7 files changed, 697 insertions, 0 deletions
| diff --git a/keyboards/handwired/traveller/Makefile b/keyboards/handwired/traveller/Makefile new file mode 100644 index 0000000000..12a4b71f4e --- /dev/null +++ b/keyboards/handwired/traveller/Makefile @@ -0,0 +1,89 @@ + +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +#     This will define a symbol, F_CPU, in all source code files equal to the +#     processor frequency in Hz. You can then use this symbol in your source code to +#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done +#     automatically to create a 32-bit value in your source code. +# +#     This will be an integer division of F_USB below, as it is sourced by +#     F_USB after it has run through any CPU prescalers. Note that this value +#     does not *change* the processor frequency - it should merely be updated to +#     reflect the processor speed set externally so that the code can use accurate +#     software delays. +F_CPU = 16000000 + +# for avr upload +USB ?= /dev/cu.usbmodem1421 +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +#     This will define a symbol, F_USB, in all source code files equal to the +#     input clock frequency (before any prescaling is performed) in Hz. This value may +#     differ from F_CPU if prescaling is used on the latter, and is required as the +#     raw input clock is fed directly to the PLL sections of the AVR for high speed +#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +#     at the end, this will be done automatically to create a 32-bit value in your +#     source code. +# +#     If no clock division is performed on the input clock inside the AVR (via the +#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + + +ifdef TEENSY2 +    OPT_DEFS += -DATREUS_TEENSY2 +    ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex +else +    OPT_DEFS += -DATREUS_ASTAR +    OPT_DEFS += -DCATERINA_BOOTLOADER +    ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ +                            avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) +endif +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# MCU name + +# Boot Section Size in *bytes* +#   Teensy halfKay   512 +#   Teensy++ halfKay 1024 +#   Atmel DFU loader 4096 +#   LUFA bootloader  4096 +#   USBaspLoader     2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +#   change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes       # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes       # Audio control and System control(+450) +CONSOLE_ENABLE ?= no        # Console for debug(+400) +COMMAND_ENABLE ?= no        # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no            # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no            # MIDI controls +UNICODE_ENABLE ?= no         # Unicode +BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no           # Audio output on port C6 +RGBLIGHT_ENABLE = yes + +ifndef QUANTUM_DIR +	include ../../../Makefile +endif + +upload: build +	$(ATREUS_UPLOAD_COMMAND) + diff --git a/keyboards/handwired/traveller/config.h b/keyboards/handwired/traveller/config.h new file mode 100644 index 0000000000..2b82da447f --- /dev/null +++ b/keyboards/handwired/traveller/config.h @@ -0,0 +1,173 @@ +/* +Copyright 2012 Jun Wako <[email protected]> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program.  If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID       0xFEED +#define PRODUCT_ID      0x6060 +#define DEVICE_VER      0x0001 +#define MANUFACTURER    You +#define PRODUCT         traveller +#define DESCRIPTION     A custom keyboard + +/* key matrix size */ +#define MATRIX_ROWS 4  +#define MATRIX_COLS 13  + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { D0, D1, D3, D2 } + // no I can't say why this order seemed like a good idea +#define MATRIX_COL_PINS { B5, D6, B7, B6, F6, B1, B3, F7, B4, E6, D7, C6, D4 } +#define UNUSED_PINS + +// LED stuff +#define RGB_DI_PIN B2 +//#define RBLIGHT_TIMER +#define RGBLED_NUM 1     // Number of LEDs +#define RGBLIGHT_HUE_STEP 10 +#define RGBLIGHT_SAT_STEP 17 +#define RGBLIGHT_VAL_STEP 17 + + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW +  +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +//#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ +    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1          H +//#define MAGIC_KEY_HELP2          SLASH +//#define MAGIC_KEY_DEBUG          D +//#define MAGIC_KEY_DEBUG_MATRIX   X +//#define MAGIC_KEY_DEBUG_KBD      K +//#define MAGIC_KEY_DEBUG_MOUSE    M +//#define MAGIC_KEY_VERSION        V +//#define MAGIC_KEY_STATUS         S +//#define MAGIC_KEY_CONSOLE        C +//#define MAGIC_KEY_LAYER0_ALT1    ESC +//#define MAGIC_KEY_LAYER0_ALT2    GRAVE +//#define MAGIC_KEY_LAYER0         0 +//#define MAGIC_KEY_LAYER1         1 +//#define MAGIC_KEY_LAYER2         2 +//#define MAGIC_KEY_LAYER3         3 +//#define MAGIC_KEY_LAYER4         4 +//#define MAGIC_KEY_LAYER5         5 +//#define MAGIC_KEY_LAYER6         6 +//#define MAGIC_KEY_LAYER7         7 +//#define MAGIC_KEY_LAYER8         8 +//#define MAGIC_KEY_LAYER9         9 +//#define MAGIC_KEY_BOOTLOADER     PAUSE +//#define MAGIC_KEY_LOCK           CAPS +//#define MAGIC_KEY_EEPROM         E +//#define MAGIC_KEY_NKRO           N +//#define MAGIC_KEY_SLEEP_LED      Z + +/* + * Feature disable options + *  These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/handwired/traveller/keymaps/default/keymap.c b/keyboards/handwired/traveller/keymaps/default/keymap.c new file mode 100644 index 0000000000..13d889ab8b --- /dev/null +++ b/keyboards/handwired/traveller/keymaps/default/keymap.c @@ -0,0 +1,305 @@ +#include "traveller.h" +#include "mousekey.h" +#include "action_layer.h" + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +#define _QW 0 +#define _LW 1 +#define _HI 2 +#define _NAV 4 +#define _CUR 5 +#define _FKEYS 6  +#define _TRNS 8 + +// We do the same trick for functions +#define  RGBLED_TOGGLE 10 +#define _HIOUT 15 +#define _LWOUT 16 +// Macros +#define  MDL 4 +#define  MDR 5 +#define  MUR 6 +#define  MUL 3  + + + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +/* Qwerty + * ,-----------------------------------------.      .-----------------------------------------. + * | NAV  | ` ~  |   W  |   E  |   R  |   T  |      |  Y   |   U  |   I  |   O  |  -   |  =   | + * |------+------+------+------+------+------|      |------+------+------+------+------+------| + * | Tab  |   Q  |   S  |   D  |   F  |   G  |      |  H   |  J   |   K  |   L  |   P  |  \   | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + *|ctrl/esc|  A  |   X  |   C  |   V  |   B  |Ctrl /|   N  |   M  |   ,  |   .  |   ;  |  '   | + * |------+------+------+------+------+------+  //  +------+------+------+------+------+------| + * | Shift|   Z  | Del  | GUI  | Low  | Bspc |/Enter| Spc  | Hi   | GUI  | Alt  |  /   |Shift | + * `------------------------------------------------------------------------------------------' + *  + */ +[_QW] = KEYMAP(  +  F(_NAV),          KC_GRV, KC_W,    KC_E,    KC_R,    KC_T,             KC_Y,    KC_U,    KC_I,    KC_O,    KC_MINS,  KC_EQL, +  KC_TAB,           KC_Q,    KC_S,    KC_D,    KC_F,    KC_G,            KC_H,    KC_J,    KC_K,    KC_L,    KC_P, 	KC_BSLS, +  CTL_T(KC_ESC),    KC_A,    KC_X,    KC_C,    KC_V,    KC_B,    KC_RCTL,  KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SCLN, 	KC_QUOT, +  KC_LSFT, KC_Z,    KC_DEL, KC_LGUI, MO(_LW), KC_BSPC, KC_ENTER, KC_SPC,  MO(_HI), KC_RGUI, KC_RALT,    KC_SLSH,   KC_RSFT + ), + +/* LOW  - numbers, missing or awkward programming keys + Doubled 1 key allows lazy reach with ring finger.  + * ,-----------------------------------------.      .-----------------------------------------. + * | FKeys|   1  |   2  |  3   |   4  |   5  |      |  6   |  7   |   8  |   9  |   0  |Ctrl-alt-del| + * |------+------+------+------+------+------|      +------+------+------+------+------+------| + * | Tab  |   1  |  ]   |  (   |  )   |      |      |   *  |   (  |   )  |   [  |      |      | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + * | Caps |  [   |      |  {   |   }  |  `   |     /|   #  |   {  |   }  |      | ]    |      | + * |------+------+------+------+------+------+  //  +------+------+------+------+------+------| + * | Shift|      |      |      | Low  |      |/     |      |  Hi  |      |      |      |Shift | + * `------------------------------------------------------------------------------------------' + *  + */ + +[_LW] = KEYMAP(  +  F(_FKEYS),   KC_1,     KC_2,      KC_3,     KC_4,    KC_5,             KC_6,    KC_7,       KC_8,      KC_9,    KC_0,  LCTL(LALT(KC_DEL)) , +  KC_TRNS,  KC_1,     KC_RBRC,   KC_LPRN,  KC_RPRN, KC_NO,               KC_ASTR, KC_LPRN,    KC_RPRN,    KC_LBRC,    KC_NO, KC_NO, +  KC_CAPS,   KC_LBRC,  KC_NO,     KC_LCBR,  KC_RCBR, KC_TILD,   KC_TRNS,  KC_HASH, KC_LCBR,    KC_RCBR,   KC_NO,    KC_RBRC,   KC_NO, +  KC_TRNS,  KC_TRNS,  KC_TRNS,   KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS,    KC_TRNS,   KC_TRNS,  KC_TRNS,  KC_TRNS +), + +/* HI - Punctuation, shell and  +url ://@.com  row on bottom,    && is opposite ||       ^$ are in regex order: ^.*$     +Right hand nav keys work pretty well chorded with the Right hand Hi Key + * ,-----------------------------------------.      .-----------------------------------------. + * |FKEYS |   !  |   @  |   #  |   $  |   %  |      |  ^   |   &  |   *  |   (  |   )  |   +  | + * |------+------+------+------+------+------|      |------+------+------+------+------+------| + * |      |  !   |  &   |  "|" |   $  |   %  |      |  Vol+|  Mute|      |      |      |      | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + * | CAPS |  ^   |   :  |   .  |   *  |   -  |     /|  Vol-| Play | PgUp | Home | Up   | End  | + * |------+------+------+------+------+------+  //  +------+------+------+------+------+------| + * |      |   /  |      |      | Low  |      |/     |      |  Hi  | PgDn | Left| Down | Right | + * `------------------------------------------------------------------------------------------' + *  + */ + +[_HI] = KEYMAP(  + F(_FKEYS), KC_EXLM,  KC_AT,   KC_HASH,  KC_DLR,   KC_PERC,           KC_CIRC,  KC_AMPR,    KC_ASTR,   KC_LPRN,  KC_RPRN,  KC_PLUS, + KC_TRNS, KC_EXLM,  KC_AMPR, KC_PIPE,  KC_DLR,   KC_PERC,             KC_VOLU, KC_MUTE,    KC_NO,     KC_NO,    KC_NO,    KC_NO,  + KC_CAPS, KC_CIRC,  KC_COLN,  KC_DOT,  KC_ASTR,  KC_MINS,   KC_TRNS,  KC_VOLD, KC_PPLS,    KC_PGUP,   KC_HOME,  KC_UP,    KC_END, + KC_TRNS, KC_SLSH,  KC_TRNS,  KC_TRNS, F(_LW),   KC_TRNS,   KC_TRNS,  KC_TRNS, KC_TRNS,    KC_PGDN,   KC_LEFT,  KC_DOWN,  KC_RIGHT  +),	 + +/* NAV - mouse &  navigation +//gui left and right are line home/end, or fore & back in browser +// Mouse buttons are reversed for comfort - bigger stretch is to the right button.  + + * ,-----------------------------------------.      .-----------------------------------------. +* | NAV  |      |      | Up   |      |Gui-> |      | MwU  | MS_UL| MS_U |MS_UR |      |Ms Norm| +* |------+------+------+------+------+------|      |------+------+------+------+------+--------| +* |      |Gui<- | Left | Down |Right | C^E  |      | BTN3 | MS_L |MS Up | MS_R |      |Ms Fast | +* |------+------+------+------+------+------|------|------+------+------+------+------+--------| +* |      | C^A  | GUI X| GUI C| GUI_V|      |Enter/| MWD  | M_DL |MS Dwn|MS_DR | Up   |Ms Slow | +* |------+------+------+------+------+------+  //  +------+------+------+------+------+------| +* |      | GuiZ |      |      | Low  |      |/ButnR|ButnL |  Hi  |      | Left | Down | Right | +* `------------------------------------------------------------------------------------------' +*/ + +[_NAV] = KEYMAP(  +  F(_NAV),  KC_NO,         KC_NO,    KC_UP,       KC_NO,     RGUI(KC_RIGHT),            KC_WH_U,  M(MUL), KC_MS_U,   M(MUR), KC_NO, KC_ACL2, +  KC_TRNS, RGUI(KC_LEFT),  KC_LEFT,  KC_DOWN,     KC_RIGHT,  LCTL(KC_E),                KC_BTN3,  KC_MS_L,  KC_MS_U,   KC_MS_R,  KC_NO, KC_ACL1, +  KC_TRNS, LCTL(KC_A),     LGUI(KC_X),RGUI(KC_C), RGUI(KC_V),KC_NO,         KC_ENTER,   KC_WH_D,  M(MDL), KC_MS_D,  M(MDR),  KC_UP, KC_ACL0, +  KC_TRNS, RGUI(KC_Z),     KC_TRNS,  KC_TRNS,     KC_TRNS,   KC_TRNS,       KC_BTN2,   KC_BTN1,  KC_TRNS,  KC_TRNS,   KC_LEFT,   KC_DOWN,   KC_RIGHT +), + +/* FKEYS - Funtion keys & mac stuff + * ,-----------------------------------------.      .-----------------------------------------. + * | FKEYS| F1   | F2   | F3   |  F4  | F5   |      | F6   | F7   | F8   | F9   | F10  | Ctrl |  + * |------+------+------+------+------+------|      |------+------+------+------+------+------| + * |      |      |      |      |      |      |      |  F11 | F12  |  F13 | F14  |  F15 | Alt  | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + * |Qwerty|      |      |      |      |      |     /|      |      |      |      |      | Del  | + * |------+------+------+------+------+------+  //  +------+------+------+------+------+------| + * |    . |RGBTog|  .   |      | LO   | Bspc |/     |      | HI   |      |      |      |      | + * `------------------------------------------------------------------------------------------' + * + */  +  +[_FKEYS] = KEYMAP(  +  F(_FKEYS), KC_F1,    KC_F2,  	KC_F3,      KC_F4,     KC_F5,               KC_F6,    KC_F7,    KC_F8,    KC_F9,    KC_F10,    KC_RCTL, +  KC_TRNS,   KC_NO,    KC_NO,   KC_NO,      KC_NO,     KC_NO,               KC_F11,   KC_F12,   KC_F13,    KC_F14,  KC_F15,  	 KC_LALT , +  F(_QW),   KC_NO,     KC_NO,   KC_NO,      KC_NO,     KC_NO,    KC_TRNS,   KC_NO,    KC_NO,    KC_NO,      KC_NO,   KC_NO,    KC_DEL, +  KC_TRNS, F(RGBLED_TOGGLE),    KC_TRNS,    KC_TRNS,   KC_TRNS,  KC_TRNS,   KC_TRNS,   KC_TRNS,  KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS +), + + +/* TRNS - skeleton for laters + * ,-----------------------------------------.      .-----------------------------------------. + * |   .  |   .  |   .  |   .  |   .  |   .  |      |  ^   |   &  |   *  |   (  |   )  |      | + * |------+------+------+------+------+------|      |------+------+------+------+------+------| + * |   .  |   .  |   .  |   .  |   .  |   .  |      |  6   |  7   |   8  |   9  |   0  |      | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + * |   .  |   .  |   .  |   .  |   .  |   .  |     /|      |      |      |   .  |   ;  |  "   | + * |------+------+------+------+------+------+  //  +------+------+------+------+------+------| + * |    . |   .  |  .   | GUI  |  LO  |   .  |/     | Spc  |  HI  | GUI  |  M0  |  /   |LSFT | + * `------------------------------------------------------------------------------------------' + *  + */ + +[_TRNS] = { +  {KC_TRNS,  KC_TRNS,   KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_NO,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS}, +  {KC_TRNS,  KC_TRNS,   KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_NO,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS, 	KC_TRNS}, +  {KC_TRNS,  KC_TRNS,   KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS,  KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS, 	KC_TRNS}, +  {KC_TRNS, KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS,  KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS} + } + + +}; + + +const uint16_t PROGMEM fn_actions[] = { +    [_QW] = ACTION_LAYER_ON(_QW,ON_RELEASE), // return to QWERTY  layer +    [_LW] = ACTION_LAYER_TAP_TOGGLE(_LW), // Turn on LW when holding, or tap 3 times to switch +    [_HI] = ACTION_LAYER_TAP_TOGGLE(_HI), // Turn on LW when holding, or tap 3 times to switch                +    [_NAV] = ACTION_LAYER_TOGGLE(_NAV),                                    +    [_FKEYS] = ACTION_LAYER_TOGGLE(_FKEYS),   +    [_LWOUT] = ACTION_LAYER_OFF(_LW,ON_RELEASE), +    [_HIOUT] = ACTION_LAYER_OFF(_HI,ON_RELEASE), +     +    // Functions +  [RGBLED_TOGGLE]  = ACTION_FUNCTION(RGBLED_TOGGLE), +  +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ +  // MACRODOWN only works in this function +      switch(id) { +        case 0: +          if (record->event.pressed) { +            register_code(KC_RSFT); +            #ifdef BACKLIGHT_ENABLE +              backlight_step(); +            #endif +          } else { +            unregister_code(KC_RSFT); +          } +        break; + +   // from  algernon's ErgoDox EZ layout, +       case MUL: +        if (record->event.pressed) { +          mousekey_on(KC_MS_UP); +          mousekey_on(KC_MS_LEFT); +        } else { +          mousekey_off(KC_MS_UP); +          mousekey_off(KC_MS_LEFT); +        } +        mousekey_send(); +        break; + +      case MUR: +        if (record->event.pressed) { +          mousekey_on(KC_MS_UP); +          mousekey_on(KC_MS_RIGHT); +        } else { +          mousekey_off(KC_MS_UP); +          mousekey_off(KC_MS_RIGHT); +        } +        mousekey_send(); +        break; + +      case MDL: +        if (record->event.pressed) { +          mousekey_on(KC_MS_DOWN); +          mousekey_on(KC_MS_LEFT); +        } else { +          mousekey_off(KC_MS_DOWN); +          mousekey_off(KC_MS_LEFT); +        } +        mousekey_send(); +        break; + +      case MDR: +        if (record->event.pressed) { +          mousekey_on(KC_MS_DOWN); +          mousekey_on(KC_MS_RIGHT); +        } else { +          mousekey_off(KC_MS_DOWN); +          mousekey_off(KC_MS_RIGHT); +        } +        mousekey_send(); +        break; + + +      } +    return MACRO_NONE; +}; + + + +void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { +  switch (id) { +    case RGBLED_TOGGLE: +      //led operations +      if (record->event.pressed) { +        rgblight_toggle(); +      } +        break; +  } +} + +  + +void LayerLEDSet(uint8_t layr) { + +    switch (layr) { +        case _QW: +            rgblight_setrgb(0,20, 0); //  dim green +        break; +        case _LW: +            // deep purple +            rgblight_setrgb(20,0,35);  +            break;   +        case _HI: +            // light blue +           rgblight_setrgb(0,20,20);  +            break;     +        case _NAV: +            // Yellowy orange +            rgblight_setrgb(25,20,0); // brighter +            break; +        case _FKEYS: +         // RED +           rgblight_setrgb(20,0,0); // brighter +            break;   +        default: +            rgblight_setrgb(20,2,20);//error +            break; +    } +  + return; +   +} + +void matrix_init_user(void) { +} + +// Bleah globals need to be initialized. +uint8_t old_layer=_QW; + +void matrix_scan_user(void) { +         uint8_t layer = biton32(layer_state); +         if (old_layer != layer) { +           LayerLEDSet(layer); +           old_layer=layer; +           } +} + + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { +  return true; +} + +void led_set_user(uint8_t usb_led) { + +} + + diff --git a/keyboards/handwired/traveller/keymaps/default/readme.md b/keyboards/handwired/traveller/keymaps/default/readme.md new file mode 100644 index 0000000000..7ddc40b3c3 --- /dev/null +++ b/keyboards/handwired/traveller/keymaps/default/readme.md @@ -0,0 +1,2 @@ +# The default keymap for handwired/traveller +this is a kitchen sink build  diff --git a/keyboards/handwired/traveller/readme.md b/keyboards/handwired/traveller/readme.md new file mode 100644 index 0000000000..646844b1d7 --- /dev/null +++ b/keyboards/handwired/traveller/readme.md @@ -0,0 +1,35 @@ +traveler keyboard firmware +====================== + +## Traveller Specific Info ## +The traveller is a varient on the atreus keyboard.  +Like the Atreus, it is designed to be a good compromise between size and ergonomics.  + +key differences are  +- an additional column for each pinky +- an RGB LED in the center to show the current layer +- more finger stagger,  splay angle and contoured keycaps (F2 profile for space key).  + +You can make your own traveller  keyboard by using the openscad tools from the atreus repository, and adding a hole for the LED to shine through.  + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent README.md](/README.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboard/traveler folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file.  + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default +To build with the default keymap, simply run `make`. + +### Other Keymaps +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` and see keymap document (you can find in top README.md) and existent keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +``` +$ make KEYMAP=[default|jack|<name>] +``` +Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder. diff --git a/keyboards/handwired/traveller/traveller.c b/keyboards/handwired/traveller/traveller.c new file mode 100644 index 0000000000..9d25341300 --- /dev/null +++ b/keyboards/handwired/traveller/traveller.c @@ -0,0 +1,61 @@ +#include "traveller.h" + +__attribute__ ((weak)) +void matrix_init_user(void) { +        // leave this function blank - it can be defined in a keymap file +}; + +__attribute__ ((weak)) +void matrix_scan_user(void) { +        // leave this function blank - it can be defined in a keymap file +} + +__attribute__ ((weak)) +void process_action_user(keyrecord_t *record) { +        // leave this function blank - it can be defined in a keymap file +} + +__attribute__ ((weak)) +void led_set_user(uint8_t usb_led) { +        // leave this function blank - it can be defined in a keymap file +} + +void matrix_init_kb(void) { +        // put your keyboard start-up code here +        // runs once when the firmware starts up + +#ifdef RGBLIGHT_ENABLE +        rgblight_init(); +        rgblight_mode(1); // solid, no timer +        rgblight_setrgb(0,20,0);// dim green, happens to be same as _QW +#endif + +// Turn status LED on +        DDRC |= (1<<7); +        PORTC |= (1<<7); + +        matrix_init_user(); +} + + +void matrix_scan_kb(void) { +	// put your looping keyboard code here +	// runs every cycle (a lot) + +	matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { +	// put your per-action keyboard code here +	// runs for every action, just before processing by the firmware + +	return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { +	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + +	led_set_user(usb_led); +} + + diff --git a/keyboards/handwired/traveller/traveller.h b/keyboards/handwired/traveller/traveller.h new file mode 100644 index 0000000000..972a1a94a6 --- /dev/null +++ b/keyboards/handwired/traveller/traveller.h @@ -0,0 +1,32 @@ +#ifndef TRAVELLER_H +#define TRAVELLER_H + +#include "quantum.h" +#include "led.h" + +#ifdef RGBLIGHT_ENABLE +  #include "rgblight.h" +#endif +#ifdef BACKLIGHT_ENABLE +        #include "backlight.h" +#endif + + + +// This a shortcut to help you visually see your layout. +// The first section contains all of the arguements +// The second converts the arguments into a two-dimensional array +#define KEYMAP( \ +        k00, k01, k02, k03, k04, k05,       k07, k08, k09, k0a, k0b, k0c, \ +        k10, k11, k12, k13, k14, k15,       k17, k18, k19, k1a, k1b, k1c, \ +        k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, \ +        k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c  \ +) \ +{ \ +        { k00, k01, k02, k03, k04, k05, KC_NO, k07, k08, k09, k0a, k0b, k0c }, \ +        { k10, k11, k12, k13, k14, k15, KC_NO, k17, k18, k19, k1a, k1b, k1c }, \ +        { k20, k21, k22, k23, k24, k25, k26,   k27, k28, k29, k2a, k2b, k2c }, \ +        { k30, k31, k32, k33, k34, k35, k36,   k37, k38, k39, k3a, k3b, k3c } \ +} + +#endif | 
