diff options
| -rw-r--r-- | keyboards/tv44/Makefile | 75 | ||||
| -rw-r--r-- | keyboards/tv44/config.h | 162 | ||||
| -rw-r--r-- | keyboards/tv44/keymaps/default/Makefile | 21 | ||||
| -rw-r--r-- | keyboards/tv44/keymaps/default/config.h | 8 | ||||
| -rw-r--r-- | keyboards/tv44/keymaps/default/keymap.c | 97 | ||||
| -rw-r--r-- | keyboards/tv44/keymaps/default/readme.md | 1 | ||||
| -rw-r--r-- | keyboards/tv44/keymaps/xyverz/Makefile | 21 | ||||
| -rw-r--r-- | keyboards/tv44/keymaps/xyverz/config.h | 8 | ||||
| -rw-r--r-- | keyboards/tv44/keymaps/xyverz/keymap.c | 92 | ||||
| -rw-r--r-- | keyboards/tv44/keymaps/xyverz/readme.md | 1 | ||||
| -rw-r--r-- | keyboards/tv44/readme.md | 28 | ||||
| -rw-r--r-- | keyboards/tv44/tv44.c | 28 | ||||
| -rw-r--r-- | keyboards/tv44/tv44.h | 22 | 
13 files changed, 564 insertions, 0 deletions
| diff --git a/keyboards/tv44/Makefile b/keyboards/tv44/Makefile new file mode 100644 index 0000000000..45ca127807 --- /dev/null +++ b/keyboards/tv44/Makefile @@ -0,0 +1,75 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +#     This will define a symbol, F_CPU, in all source code files equal to the +#     processor frequency in Hz. You can then use this symbol in your source code to +#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done +#     automatically to create a 32-bit value in your source code. +# +#     This will be an integer division of F_USB below, as it is sourced by +#     F_USB after it has run through any CPU prescalers. Note that this value +#     does not *change* the processor frequency - it should merely be updated to +#     reflect the processor speed set externally so that the code can use accurate +#     software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +#     This will define a symbol, F_USB, in all source code files equal to the +#     input clock frequency (before any prescaling is performed) in Hz. This value may +#     differ from F_CPU if prescaling is used on the latter, and is required as the +#     raw input clock is fed directly to the PLL sections of the AVR for high speed +#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +#     at the end, this will be done automatically to create a 32-bit value in your +#     source code. +# +#     If no clock division is performed on the input clock inside the AVR (via the +#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +#   Teensy halfKay   512 +#   Teensy++ halfKay 1024 +#   Atmel DFU loader 4096 +#   LUFA bootloader  4096 +#   USBaspLoader     2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +#   change yes to no to disable +# +BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes        # Console for debug(+400) +COMMAND_ENABLE ?= yes        # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= yes           # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no            # MIDI controls +UNICODE_ENABLE ?= no         # Unicode +BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no           # Audio output on port C6 + +ifndef QUANTUM_DIR +	include ../../Makefile +endif + + diff --git a/keyboards/tv44/config.h b/keyboards/tv44/config.h new file mode 100644 index 0000000000..0ae93c0957 --- /dev/null +++ b/keyboards/tv44/config.h @@ -0,0 +1,162 @@ +/* +Copyright 2012 Jun Wako <[email protected]> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program.  If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID       0xFEAE +#define PRODUCT_ID      0x8844 +#define DEVICE_VER      0x0002 +#define MANUFACTURER    Evan Sailer +#define PRODUCT         TheVan 44 +#define DESCRIPTION     keyboard firmware for TV44 + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 12 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { D7, B5, F7, D4 } +#define MATRIX_COL_PINS { D2, D3, D5, D6, B4, B6, F6, F5, F4, F1, F0, B3 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW +  +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ +    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1          H +//#define MAGIC_KEY_HELP2          SLASH +//#define MAGIC_KEY_DEBUG          D +//#define MAGIC_KEY_DEBUG_MATRIX   X +//#define MAGIC_KEY_DEBUG_KBD      K +//#define MAGIC_KEY_DEBUG_MOUSE    M +//#define MAGIC_KEY_VERSION        V +//#define MAGIC_KEY_STATUS         S +//#define MAGIC_KEY_CONSOLE        C +//#define MAGIC_KEY_LAYER0_ALT1    ESC +//#define MAGIC_KEY_LAYER0_ALT2    GRAVE +//#define MAGIC_KEY_LAYER0         0 +//#define MAGIC_KEY_LAYER1         1 +//#define MAGIC_KEY_LAYER2         2 +//#define MAGIC_KEY_LAYER3         3 +//#define MAGIC_KEY_LAYER4         4 +//#define MAGIC_KEY_LAYER5         5 +//#define MAGIC_KEY_LAYER6         6 +//#define MAGIC_KEY_LAYER7         7 +//#define MAGIC_KEY_LAYER8         8 +//#define MAGIC_KEY_LAYER9         9 +//#define MAGIC_KEY_BOOTLOADER     PAUSE +//#define MAGIC_KEY_LOCK           CAPS +//#define MAGIC_KEY_EEPROM         E +//#define MAGIC_KEY_NKRO           N +//#define MAGIC_KEY_SLEEP_LED      Z + +/* + * Feature disable options + *  These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/tv44/keymaps/default/Makefile b/keyboards/tv44/keymaps/default/Makefile new file mode 100644 index 0000000000..f4671a9d11 --- /dev/null +++ b/keyboards/tv44/keymaps/default/Makefile @@ -0,0 +1,21 @@ +# Build Options +#   change to "no" to disable the options, or define them in the Makefile in  +#   the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes       # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes       # Audio control and System control(+450) +CONSOLE_ENABLE = no         # Console for debug(+400) +COMMAND_ENABLE = yes        # Commands for debug and configuration +NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality +MIDI_ENABLE = no            # MIDI controls +AUDIO_ENABLE = no           # Audio output on port C6 +UNICODE_ENABLE = no         # Unicode +BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time. +SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR +	include ../../../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/tv44/keymaps/default/config.h b/keyboards/tv44/keymaps/default/config.h new file mode 100644 index 0000000000..df06a26206 --- /dev/null +++ b/keyboards/tv44/keymaps/default/config.h @@ -0,0 +1,8 @@ +#ifndef CONFIG_USER_H +#define CONFIG_USER_H + +#include "../../config.h" + +// place overrides here + +#endif
\ No newline at end of file diff --git a/keyboards/tv44/keymaps/default/keymap.c b/keyboards/tv44/keymaps/default/keymap.c new file mode 100644 index 0000000000..6a4fef3da2 --- /dev/null +++ b/keyboards/tv44/keymaps/default/keymap.c @@ -0,0 +1,97 @@ +#include "tv44.h" +#include "action_layer.h" +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. + +#define _QW 0 +#define _DV 1 +#define _CM 2 +#define _L1 3 +#define _L2 4 +#define _L3 5 + +// Macro name shortcuts +#define QWERTY M(_QW) +#define DVORAK M(_DV) +#define COLEMAK M(_CM) + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +  [_QW] = { /* Qwerty */ +    {KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC }, +    {MO(_L1), KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, MO(_L1) }, +    {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_F,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, MO(_L2) }, +    {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT,  XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_RALT, KC_ESC,  XXXXXXX, TG(_L3) } +  }, +  [_DV] = { /* Dvorak */ +    {KC_TAB,  KC_COMM, KC_DOT,  KC_SLSH, KC_Q,    KC_Q,    KC_Q,    KC_Q,    KC_Q,    KC_Q,    KC_Q,    KC_BSPC }, +    {MO(_L1), KC_A,    KC_O,    KC_E,    KC_U,    KC_I,    KC_D,    KC_H,    KC_T,    KC_N,    KC_S,    MO(_L1) }, +    {KC_LSFT, KC_SCLN, KC_Q,    KC_J,    KC_K,    KC_X,    KC_B,    KC_M,    KC_W,    KC_V,    KC_Z,    MO(_L2) }, +    {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT,  XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_RALT, KC_ESC,  XXXXXXX, TG(_L3) } +  }, +  [_CM] = { /* Colemak */ +    {KC_TAB,  KC_Q,    KC_W,    KC_F,    KC_P,    KC_G,    KC_J,    KC_L,    KC_U,    KC_Y,    KC_SCLN, KC_BSPC }, +    {MO(_L1), KC_A,    KC_R,    KC_S,    KC_T,    KC_D,    KC_H,    KC_N,    KC_E,    KC_I,    KC_O,    MO(_L1) }, +    {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_K,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, MO(_L2) }, +    {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT,  XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_RALT, KC_ESC,  XXXXXXX, TG(_L3) } +  }, +  [_L1] = { /* LAYER 1 */ +    {KC_GRV,  KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL  }, +    {_______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_DOWN, KC_UP,   KC_LEFT, KC_RGHT, _______ }, +    {_______, KC_ESC,  _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT }, +    {_______, KC_LGUI, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, XXXXXXX, _______ } +  }, +  [_L2] = { /* LAYER 2 */ +    {_______, QWERTY,  DVORAK,  COLEMAK, _______, _______, _______, KC_7,    KC_8,    KC_9,    KC_0,    _______ }, +    {KC_ESC,  KC_PIPE, KC_DQUO, KC_UNDS, KC_PLUS, LSFT(KC_LBRC), LSFT(KC_RBRC), KC_4,    KC_5,    KC_6,    KC_VOLU, KC_ENT  }, +    {_______, _______, _______, _______, _______, _______, KC_0,    KC_1,    KC_2,    KC_3,    KC_VOLD, _______ }, +    {_______, _______, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, XXXXXXX, _______ } +  }, +  [_L3] = { /* LAYER 3 */ +    {_______, _______, _______, _______, _______, _______, _______, KC_F1,   KC_F2,   KC_F3,   KC_F4,   _______ }, +    {KC_ESC,  _______, _______, _______, _______, _______, _______, KC_F5,   KC_F6,   KC_F7,   KC_F8,   _______ }, +    {KC_LSFT, KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_F9,   KC_F10,  KC_F11,  KC_F12,  _______ }, +    {_______, KC_LSFT, KC_B,    KC_SPC,  XXXXXXX, XXXXXXX, XXXXXXX, KC_C,    _______, _______, XXXXXXX, _______ } +  } +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + +void persistant_default_layer_set(uint16_t default_layer) { +  eeconfig_update_default_layer(default_layer); +  default_layer_set(default_layer); +} + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ +      switch(id) { +        case _DV: +          if (record->event.pressed) { +            persistant_default_layer_set(1UL<<_DV); +          } +          break; +        case _QW: +          if (record->event.pressed) { +            persistant_default_layer_set(1UL<<_QW); +          } +          break; +        case _CM: +          if (record->event.pressed) { +            persistant_default_layer_set(1UL<<_CM); +          } +          break; +      } +    return MACRO_NONE; +}; diff --git a/keyboards/tv44/keymaps/default/readme.md b/keyboards/tv44/keymaps/default/readme.md new file mode 100644 index 0000000000..ac84c08cfa --- /dev/null +++ b/keyboards/tv44/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for tv44
\ No newline at end of file diff --git a/keyboards/tv44/keymaps/xyverz/Makefile b/keyboards/tv44/keymaps/xyverz/Makefile new file mode 100644 index 0000000000..f4671a9d11 --- /dev/null +++ b/keyboards/tv44/keymaps/xyverz/Makefile @@ -0,0 +1,21 @@ +# Build Options +#   change to "no" to disable the options, or define them in the Makefile in  +#   the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes       # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes       # Audio control and System control(+450) +CONSOLE_ENABLE = no         # Console for debug(+400) +COMMAND_ENABLE = yes        # Commands for debug and configuration +NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality +MIDI_ENABLE = no            # MIDI controls +AUDIO_ENABLE = no           # Audio output on port C6 +UNICODE_ENABLE = no         # Unicode +BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time. +SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR +	include ../../../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/tv44/keymaps/xyverz/config.h b/keyboards/tv44/keymaps/xyverz/config.h new file mode 100644 index 0000000000..df06a26206 --- /dev/null +++ b/keyboards/tv44/keymaps/xyverz/config.h @@ -0,0 +1,8 @@ +#ifndef CONFIG_USER_H +#define CONFIG_USER_H + +#include "../../config.h" + +// place overrides here + +#endif
\ No newline at end of file diff --git a/keyboards/tv44/keymaps/xyverz/keymap.c b/keyboards/tv44/keymaps/xyverz/keymap.c new file mode 100644 index 0000000000..8cbcf8d35a --- /dev/null +++ b/keyboards/tv44/keymaps/xyverz/keymap.c @@ -0,0 +1,92 @@ +#include "tv44.h" +#include "action_layer.h" +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +#define _DV 0 +#define _QW 1 +#define _CM 2 +#define _L1 3 +#define _L2 4 + +// Macro name shortcuts +#define DVORAK M(_DV) +#define QWERTY M(_QW) +#define COLEMAK M(_CM) + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +  [_DV] = { /* 0: Dvorak */ +    {KC_TAB,  KC_QUOT, KC_COMM, KC_DOT,  KC_P,    KC_Y,    KC_F,    KC_G,    KC_C,    KC_R,    KC_L,    KC_BSPC }, +    {MO(_L1), KC_A,    KC_O,    KC_E,    KC_U,    KC_I,    KC_D,    KC_H,    KC_T,    KC_N,    KC_S,    KC_ENT  }, +    {KC_LSFT, KC_SCLN, KC_Q,    KC_J,    KC_K,    KC_X,    KC_B,    KC_M,    KC_W,    KC_V,    KC_Z,    KC_RSFT }, +    {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) } +  }, + +  [_QW] = { /* 1: Qwerty */ +    {KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC }, +    {MO(_L1), KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_ENT  }, +    {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT }, +    {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) } +  }, + +  [_CM] = { /* 2: Colemak */ +    {KC_TAB,  KC_Q,    KC_W,    KC_F,    KC_P,    KC_G,    KC_J,    KC_L,    KC_U,    KC_Y,    KC_SCLN, KC_BSPC }, +    {MO(_L1), KC_A,    KC_R,    KC_S,    KC_T,    KC_D,    KC_H,    KC_N,    KC_E,    KC_I,    KC_O,    KC_ENT  }, +    {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_K,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT }, +    {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) } +  }, + +  [_L1] = {/* 1: FN 1 */ +    {KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_DEL  }, +    {_______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_DOWN, KC_UP,   KC_LEFT, KC_RGHT, _______ }, +    {_______, _______, _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT }, +    {KC_ESC,  KC_LGUI, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, KC_SLSH, _______, _______ } +  }, + +  [_L2] = { /* 2: FN 2 */ +    {KC_ESC,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_ESC  }, +    {_______, KC_F11,  KC_F12,  _______, _______, _______, _______, _______, KC_HOME, KC_PGUP, KC_VOLU, KC_ENT  }, +    {_______, _______, _______, _______, _______, _______, _______, _______, KC_END,  KC_PGDN, KC_VOLD, _______ }, +    {QWERTY,  DVORAK,  COLEMAK, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______ } +  } + +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + +void persistant_default_layer_set(uint16_t default_layer) { +  eeconfig_update_default_layer(default_layer); +  default_layer_set(default_layer); +} + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ +      switch(id) { +        case _DV: +          if (record->event.pressed) { +            persistant_default_layer_set(1UL<<_DV); +          } +          break; +        case _QW: +          if (record->event.pressed) { +            persistant_default_layer_set(1UL<<_QW); +          } +          break; +        case _CM: +          if (record->event.pressed) { +            persistant_default_layer_set(1UL<<_CM); +          } +          break; +      } +    return MACRO_NONE; +}; + + diff --git a/keyboards/tv44/keymaps/xyverz/readme.md b/keyboards/tv44/keymaps/xyverz/readme.md new file mode 100644 index 0000000000..ac84c08cfa --- /dev/null +++ b/keyboards/tv44/keymaps/xyverz/readme.md @@ -0,0 +1 @@ +# The default keymap for tv44
\ No newline at end of file diff --git a/keyboards/tv44/readme.md b/keyboards/tv44/readme.md new file mode 100644 index 0000000000..e3b557fe2d --- /dev/null +++ b/keyboards/tv44/readme.md @@ -0,0 +1,28 @@ +tv44 keyboard firmware +====================== + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/doc/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/tv44 folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file.  + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default + +To build with the default keymap, simply run `make`. + +### Other Keymaps + +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `keymap` option like: + +``` +$ make keymap=[default|jack|<name>] +``` + +Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/`
\ No newline at end of file diff --git a/keyboards/tv44/tv44.c b/keyboards/tv44/tv44.c new file mode 100644 index 0000000000..6dc0efd28e --- /dev/null +++ b/keyboards/tv44/tv44.c @@ -0,0 +1,28 @@ +#include "tv44.h" + +void matrix_init_kb(void) { +	// put your keyboard start-up code here +	// runs once when the firmware starts up + +	matrix_init_user(); +} + +void matrix_scan_kb(void) { +	// put your looping keyboard code here +	// runs every cycle (a lot) + +	matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { +	// put your per-action keyboard code here +	// runs for every action, just before processing by the firmware + +	return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { +	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + +	led_set_user(usb_led); +} diff --git a/keyboards/tv44/tv44.h b/keyboards/tv44/tv44.h new file mode 100644 index 0000000000..4c30174acc --- /dev/null +++ b/keyboards/tv44/tv44.h @@ -0,0 +1,22 @@ +#ifndef TV44_H +#define TV44_H + +#include "quantum.h" + +// This a shortcut to help you visually see your layout. +// The following is an example using the Planck MIT layout +// The first section contains all of the arguements +// The second converts the arguments into a two-dimensional array +#define KEYMAP( \ +    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \ +    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \ +    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \ +    K30, K31, K32, K33,           K37, K38,      K39,      K3B  \ +) \ +{ \ +    { K00,   K01,   K02,   K03,  K04,   K05,   K06,   K07,   K08,   K09,   K0A,   K0B }, \ +    { K10,   K11,   K12,   K13,  K14,   K15,   K16,   K17,   K18,   K19,   K1A,   K1B }, \ +    { K20,   K21,   K22,   K23,  K24,   K25,   K26,   K27,   K28,   K29,   K2A,   K2B }, \ +    { K30,   K31,   K32,   K33,  KC_NO, KC_NO, KC_NO, K37,   K38,   K39,   K3A,   K3B }  \ + +#endif | 
