diff options
Diffstat (limited to 'Bootloaders')
-rw-r--r-- | Bootloaders/CDC/makefile | 14 | ||||
-rw-r--r-- | Bootloaders/DFU/makefile | 14 | ||||
-rw-r--r-- | Bootloaders/HID/makefile | 14 |
3 files changed, 21 insertions, 21 deletions
diff --git a/Bootloaders/CDC/makefile b/Bootloaders/CDC/makefile index 92b63dad3c..cdde8d2b95 100644 --- a/Bootloaders/CDC/makefile +++ b/Bootloaders/CDC/makefile @@ -67,8 +67,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -76,7 +76,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -86,7 +86,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Starting byte address of the bootloader, as a byte address - computed via the formula @@ -190,7 +190,7 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += -DBOOT_START_ADDR=$(BOOT_START)UL CDEFS += $(LUFA_OPTS) @@ -198,7 +198,7 @@ CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += -DBOOT_START_ADDR=$(BOOT_START)UL ADEFS += $(LUFA_OPTS) @@ -206,7 +206,7 @@ ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += -DBOOT_START_ADDR=$(BOOT_START)UL CPPDEFS += $(LUFA_OPTS) diff --git a/Bootloaders/DFU/makefile b/Bootloaders/DFU/makefile index d77933b6bb..458a6ce869 100644 --- a/Bootloaders/DFU/makefile +++ b/Bootloaders/DFU/makefile @@ -67,8 +67,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -76,7 +76,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -86,7 +86,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Starting byte address of the bootloader, as a byte address - computed via the formula @@ -185,7 +185,7 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += -DBOOT_START_ADDR=$(BOOT_START)UL CDEFS += $(LUFA_OPTS) @@ -193,7 +193,7 @@ CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += -DBOOT_START_ADDR=$(BOOT_START)UL ADEFS += $(LUFA_OPTS) @@ -201,7 +201,7 @@ ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += -DBOOT_START_ADDR=$(BOOT_START)UL CPPDEFS += $(LUFA_OPTS) diff --git a/Bootloaders/HID/makefile b/Bootloaders/HID/makefile index 6d8fbf560b..738ecc6383 100644 --- a/Bootloaders/HID/makefile +++ b/Bootloaders/HID/makefile @@ -67,8 +67,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
-# This will be an integer division of F_CLOCK below, as it is sourced by
-# F_CLOCK after it has run through any CPU prescalers. Note that this value
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
@@ -76,7 +76,7 @@ F_CPU = 8000000 # Input clock frequency.
-# This will define a symbol, F_CLOCK, in all source code files equal to the
+# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
@@ -86,7 +86,7 @@ F_CPU = 8000000 #
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_CLOCK = $(F_CPU)
+F_USB = $(F_CPU)
# Starting byte address of the bootloader, as a byte address - computed via the formula
@@ -185,7 +185,7 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources
CDEFS = -DF_CPU=$(F_CPU)UL
-CDEFS += -DF_CLOCK=$(F_CLOCK)UL
+CDEFS += -DF_USB=$(F_USB)UL
CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH)
CDEFS += -DBOOT_START_ADDR=$(BOOT_START)UL
CDEFS += $(LUFA_OPTS)
@@ -193,7 +193,7 @@ CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources
ADEFS = -DF_CPU=$(F_CPU)
-ADEFS += -DF_CLOCK=$(F_CLOCK)UL
+ADEFS += -DF_USB=$(F_USB)UL
ADEFS += -DBOARD=BOARD_$(BOARD)
ADEFS += -DBOOT_START_ADDR=$(BOOT_START)UL
ADEFS += $(LUFA_OPTS)
@@ -201,7 +201,7 @@ ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources
CPPDEFS = -DF_CPU=$(F_CPU)UL
-CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL
+CPPDEFS += -DF_USB=$(F_USB)UL
CPPDEFS += -DBOARD=BOARD_$(BOARD)
CPPDEFS += -DBOOT_START_ADDR=$(BOOT_START)UL
CPPDEFS += $(LUFA_OPTS)
|