diff options
Diffstat (limited to 'Demos/Device')
30 files changed, 210 insertions, 210 deletions
diff --git a/Demos/Device/ClassDriver/AudioInput/makefile b/Demos/Device/ClassDriver/AudioInput/makefile index 371375567b..969aa904e7 100644 --- a/Demos/Device/ClassDriver/AudioInput/makefile +++ b/Demos/Device/ClassDriver/AudioInput/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -185,20 +185,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/AudioOutput/makefile b/Demos/Device/ClassDriver/AudioOutput/makefile index 2f23514eae..dce868a965 100644 --- a/Demos/Device/ClassDriver/AudioOutput/makefile +++ b/Demos/Device/ClassDriver/AudioOutput/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -186,20 +186,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/DualVirtualSerial/makefile b/Demos/Device/ClassDriver/DualVirtualSerial/makefile index 9234fe9e6e..75d9bed97f 100644 --- a/Demos/Device/ClassDriver/DualVirtualSerial/makefile +++ b/Demos/Device/ClassDriver/DualVirtualSerial/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -182,20 +182,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/GenericHID/makefile b/Demos/Device/ClassDriver/GenericHID/makefile index b20d045d9d..d015b23fc2 100644 --- a/Demos/Device/ClassDriver/GenericHID/makefile +++ b/Demos/Device/ClassDriver/GenericHID/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -182,20 +182,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/Joystick/makefile b/Demos/Device/ClassDriver/Joystick/makefile index 23845f4b52..0ec41198c0 100644 --- a/Demos/Device/ClassDriver/Joystick/makefile +++ b/Demos/Device/ClassDriver/Joystick/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -182,20 +182,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/Keyboard/makefile b/Demos/Device/ClassDriver/Keyboard/makefile index 7981b5d034..31236f0347 100644 --- a/Demos/Device/ClassDriver/Keyboard/makefile +++ b/Demos/Device/ClassDriver/Keyboard/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -182,20 +182,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/KeyboardMouse/makefile b/Demos/Device/ClassDriver/KeyboardMouse/makefile index c4477dc00f..bc2d6914aa 100644 --- a/Demos/Device/ClassDriver/KeyboardMouse/makefile +++ b/Demos/Device/ClassDriver/KeyboardMouse/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -182,20 +182,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/KeyboardMouseMultiReport/makefile b/Demos/Device/ClassDriver/KeyboardMouseMultiReport/makefile index 9fcd9aeae3..317d26db1b 100644 --- a/Demos/Device/ClassDriver/KeyboardMouseMultiReport/makefile +++ b/Demos/Device/ClassDriver/KeyboardMouseMultiReport/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -182,20 +182,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/MIDI/makefile b/Demos/Device/ClassDriver/MIDI/makefile index 11b76deb4a..945d992038 100644 --- a/Demos/Device/ClassDriver/MIDI/makefile +++ b/Demos/Device/ClassDriver/MIDI/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -182,20 +182,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/MassStorage/makefile b/Demos/Device/ClassDriver/MassStorage/makefile index bd548f8763..0e8988fff9 100644 --- a/Demos/Device/ClassDriver/MassStorage/makefile +++ b/Demos/Device/ClassDriver/MassStorage/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -185,20 +185,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/MassStorageKeyboard/makefile b/Demos/Device/ClassDriver/MassStorageKeyboard/makefile index 1d7eaca538..c044a89fb5 100644 --- a/Demos/Device/ClassDriver/MassStorageKeyboard/makefile +++ b/Demos/Device/ClassDriver/MassStorageKeyboard/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -185,20 +185,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/Mouse/makefile b/Demos/Device/ClassDriver/Mouse/makefile index 317005f3ae..792682bf17 100644 --- a/Demos/Device/ClassDriver/Mouse/makefile +++ b/Demos/Device/ClassDriver/Mouse/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -182,20 +182,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/RNDISEthernet/makefile b/Demos/Device/ClassDriver/RNDISEthernet/makefile index 910452b7da..e3044c8862 100644 --- a/Demos/Device/ClassDriver/RNDISEthernet/makefile +++ b/Demos/Device/ClassDriver/RNDISEthernet/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -200,20 +200,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/VirtualSerial/makefile b/Demos/Device/ClassDriver/VirtualSerial/makefile index fb7dd779fa..98d3d72e99 100644 --- a/Demos/Device/ClassDriver/VirtualSerial/makefile +++ b/Demos/Device/ClassDriver/VirtualSerial/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -182,20 +182,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/ClassDriver/VirtualSerialMassStorage/makefile b/Demos/Device/ClassDriver/VirtualSerialMassStorage/makefile index 658e8db30d..a697518335 100644 --- a/Demos/Device/ClassDriver/VirtualSerialMassStorage/makefile +++ b/Demos/Device/ClassDriver/VirtualSerialMassStorage/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
-# This will be an integer division of F_CLOCK below, as it is sourced by
-# F_CLOCK after it has run through any CPU prescalers. Note that this value
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
@@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency.
-# This will define a symbol, F_CLOCK, in all source code files equal to the
+# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
@@ -98,7 +98,7 @@ F_CPU = 8000000 #
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_CLOCK = $(F_CPU)
+F_USB = $(F_CPU)
# Output format. (can be srec, ihex, binary)
@@ -184,20 +184,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources
CDEFS = -DF_CPU=$(F_CPU)UL
-CDEFS += -DF_CLOCK=$(F_CLOCK)UL
+CDEFS += -DF_USB=$(F_USB)UL
CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH)
CDEFS += $(LUFA_OPTS)
# Place -D or -U options here for ASM sources
ADEFS = -DF_CPU=$(F_CPU)
-ADEFS += -DF_CLOCK=$(F_CLOCK)UL
+ADEFS += -DF_USB=$(F_USB)UL
ADEFS += -DBOARD=BOARD_$(BOARD)
ADEFS += $(LUFA_OPTS)
# Place -D or -U options here for C++ sources
CPPDEFS = -DF_CPU=$(F_CPU)UL
-CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL
+CPPDEFS += -DF_USB=$(F_USB)UL
CPPDEFS += -DBOARD=BOARD_$(BOARD)
CPPDEFS += $(LUFA_OPTS)
#CPPDEFS += -D__STDC_LIMIT_MACROS
diff --git a/Demos/Device/ClassDriver/VirtualSerialMouse/makefile b/Demos/Device/ClassDriver/VirtualSerialMouse/makefile index 2ed7afddf6..a4ed81b565 100644 --- a/Demos/Device/ClassDriver/VirtualSerialMouse/makefile +++ b/Demos/Device/ClassDriver/VirtualSerialMouse/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -182,20 +182,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/Incomplete/Sideshow/makefile b/Demos/Device/Incomplete/Sideshow/makefile index 9439e1d9ef..22c5c76dfc 100644 --- a/Demos/Device/Incomplete/Sideshow/makefile +++ b/Demos/Device/Incomplete/Sideshow/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -186,20 +186,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/Incomplete/TestAndMeasurement/makefile b/Demos/Device/Incomplete/TestAndMeasurement/makefile index 298cd2281c..2f21e10274 100644 --- a/Demos/Device/Incomplete/TestAndMeasurement/makefile +++ b/Demos/Device/Incomplete/TestAndMeasurement/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -182,20 +182,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/LowLevel/AudioInput/makefile b/Demos/Device/LowLevel/AudioInput/makefile index 40746f8f93..520abbebdd 100644 --- a/Demos/Device/LowLevel/AudioInput/makefile +++ b/Demos/Device/LowLevel/AudioInput/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -184,20 +184,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/LowLevel/AudioOutput/makefile b/Demos/Device/LowLevel/AudioOutput/makefile index 28bc1c286a..1623cf1557 100644 --- a/Demos/Device/LowLevel/AudioOutput/makefile +++ b/Demos/Device/LowLevel/AudioOutput/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -185,20 +185,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/LowLevel/DualVirtualSerial/makefile b/Demos/Device/LowLevel/DualVirtualSerial/makefile index 6808429211..f245a58dc0 100644 --- a/Demos/Device/LowLevel/DualVirtualSerial/makefile +++ b/Demos/Device/LowLevel/DualVirtualSerial/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -181,20 +181,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/LowLevel/GenericHID/makefile b/Demos/Device/LowLevel/GenericHID/makefile index d87f6dc69e..3c707fcc81 100644 --- a/Demos/Device/LowLevel/GenericHID/makefile +++ b/Demos/Device/LowLevel/GenericHID/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -181,20 +181,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/LowLevel/Joystick/makefile b/Demos/Device/LowLevel/Joystick/makefile index ba9c158990..ff10a659a4 100644 --- a/Demos/Device/LowLevel/Joystick/makefile +++ b/Demos/Device/LowLevel/Joystick/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -181,20 +181,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/LowLevel/Keyboard/makefile b/Demos/Device/LowLevel/Keyboard/makefile index 3e764d9d72..7f29e0631b 100644 --- a/Demos/Device/LowLevel/Keyboard/makefile +++ b/Demos/Device/LowLevel/Keyboard/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -181,20 +181,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/LowLevel/KeyboardMouse/makefile b/Demos/Device/LowLevel/KeyboardMouse/makefile index 12490fc614..98f9e12854 100644 --- a/Demos/Device/LowLevel/KeyboardMouse/makefile +++ b/Demos/Device/LowLevel/KeyboardMouse/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -181,20 +181,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/LowLevel/MIDI/makefile b/Demos/Device/LowLevel/MIDI/makefile index 7b8a242c49..079fae94b9 100644 --- a/Demos/Device/LowLevel/MIDI/makefile +++ b/Demos/Device/LowLevel/MIDI/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -181,20 +181,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/LowLevel/MassStorage/makefile b/Demos/Device/LowLevel/MassStorage/makefile index becdfab0f5..7e72a987a2 100644 --- a/Demos/Device/LowLevel/MassStorage/makefile +++ b/Demos/Device/LowLevel/MassStorage/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -184,20 +184,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/LowLevel/Mouse/makefile b/Demos/Device/LowLevel/Mouse/makefile index 7b8d8eea21..a962a80d29 100644 --- a/Demos/Device/LowLevel/Mouse/makefile +++ b/Demos/Device/LowLevel/Mouse/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -181,20 +181,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/LowLevel/RNDISEthernet/makefile b/Demos/Device/LowLevel/RNDISEthernet/makefile index 66528646dd..37d90f9bca 100644 --- a/Demos/Device/LowLevel/RNDISEthernet/makefile +++ b/Demos/Device/LowLevel/RNDISEthernet/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -200,20 +200,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS diff --git a/Demos/Device/LowLevel/VirtualSerial/makefile b/Demos/Device/LowLevel/VirtualSerial/makefile index fd13fc64e6..ba8911850e 100644 --- a/Demos/Device/LowLevel/VirtualSerial/makefile +++ b/Demos/Device/LowLevel/VirtualSerial/makefile @@ -79,8 +79,8 @@ BOARD = USBKEY # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. @@ -88,7 +88,7 @@ F_CPU = 8000000 # Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the +# This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed @@ -98,7 +98,7 @@ F_CPU = 8000000 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) +F_USB = $(F_CPU) # Output format. (can be srec, ihex, binary) @@ -181,20 +181,20 @@ CSTANDARD = -std=c99 # Place -D or -U options here for C sources CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL +CDEFS += -DF_USB=$(F_USB)UL CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) CDEFS += $(LUFA_OPTS) # Place -D or -U options here for ASM sources ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL +ADEFS += -DF_USB=$(F_USB)UL ADEFS += -DBOARD=BOARD_$(BOARD) ADEFS += $(LUFA_OPTS) # Place -D or -U options here for C++ sources CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL +CPPDEFS += -DF_USB=$(F_USB)UL CPPDEFS += -DBOARD=BOARD_$(BOARD) CPPDEFS += $(LUFA_OPTS) #CPPDEFS += -D__STDC_LIMIT_MACROS |