diff options
Diffstat (limited to 'docs/feature_rgb_matrix.md')
| -rw-r--r-- | docs/feature_rgb_matrix.md | 73 | 
1 files changed, 54 insertions, 19 deletions
| diff --git a/docs/feature_rgb_matrix.md b/docs/feature_rgb_matrix.md index fe72d063e4..2b9ee5c520 100644 --- a/docs/feature_rgb_matrix.md +++ b/docs/feature_rgb_matrix.md @@ -10,7 +10,7 @@ If you want to use single color LED's you should use the [LED Matrix Subsystem](  There is basic support for addressable RGB matrix lighting with the I2C IS31FL3731 RGB controller. To enable it, add this to your `rules.mk`: -```makefile +```make  RGB_MATRIX_ENABLE = yes  RGB_MATRIX_DRIVER = IS31FL3731  ``` @@ -21,6 +21,7 @@ You can use between 1 and 4 IS31FL3731 IC's. Do not specify `DRIVER_ADDR_<N>` de  |----------|-------------|---------|  | `ISSI_TIMEOUT` | (Optional) How long to wait for i2c messages, in milliseconds | 100 |  | `ISSI_PERSISTENCE` | (Optional) Retry failed messages this many times | 0 | +| `ISSI_3731_DEGHOST` | (Optional) Set this define to enable de-ghosting by halving Vcc during blanking time | |  | `DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |  | `DRIVER_LED_TOTAL` | (Required) How many RGB lights are present across all drivers | |  | `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | | @@ -49,6 +50,8 @@ Here is an example using 2 drivers.  !> Note the parentheses, this is so when `DRIVER_LED_TOTAL` is used in code and expanded, the values are added together before any additional math is applied to them. As an example, `rand() % (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)` will give very different results than `rand() % DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL`. +For split keyboards using `RGB_MATRIX_SPLIT` with an LED driver, you can either have the same driver address or different driver addresses. If using different addresses, use `DRIVER_ADDR_1` for one and `DRIVER_ADDR_2` for the other one. Then, in `g_is31_leds`, fill out the correct driver index (0 or 1). If using one address, use `DRIVER_ADDR_1` for both, and use index 0 for `g_is31_leds`. +  Define these arrays listing all the LEDs in your `<keyboard>.c`:  ```c @@ -71,7 +74,7 @@ Where `Cx_y` is the location of the LED in the matrix defined by [the datasheet]  There is basic support for addressable RGB matrix lighting with the I2C IS31FL3733 RGB controller. To enable it, add this to your `rules.mk`: -```makefile +```make  RGB_MATRIX_ENABLE = yes  RGB_MATRIX_DRIVER = IS31FL3733  ``` @@ -82,6 +85,9 @@ You can use between 1 and 4 IS31FL3733 IC's. Do not specify `DRIVER_ADDR_<N>` de  |----------|-------------|---------|  | `ISSI_TIMEOUT` | (Optional) How long to wait for i2c messages, in milliseconds | 100 |  | `ISSI_PERSISTENCE` | (Optional) Retry failed messages this many times | 0 | +| `ISSI_PWM_FREQUENCY` | (Optional) PWM Frequency Setting - IS31FL3733B only | 0 | +| `ISSI_SWPULLUP` | (Optional) Set the value of the SWx lines on-chip de-ghosting resistors | PUR_0R (Disabled) | +| `ISSI_CSPULLUP` | (Optional) Set the value of the CSx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |  | `DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |  | `DRIVER_LED_TOTAL` | (Required) How many RGB lights are present across all drivers | |  | `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | | @@ -93,6 +99,18 @@ You can use between 1 and 4 IS31FL3733 IC's. Do not specify `DRIVER_ADDR_<N>` de  | `DRIVER_SYNC_3` | (Optional) Sync configuration for the third RGB driver | 0 |  | `DRIVER_SYNC_4` | (Optional) Sync configuration for the fourth RGB driver | 0 | +The IS31FL3733 IC's have on-chip resistors that can be enabled to allow for de-ghosting of the RGB matrix. By default these resistors are not enabled (`ISSI_SWPULLUP`/`ISSI_CSPULLUP` are given the value of`PUR_0R`), the values that can be set to enable de-ghosting are as follows: + +| `ISSI_SWPULLUP/ISSI_CSPULLUP` | Description | +|----------------------|-------------| +| `PUR_0R` | (default) Do not use the on-chip resistors/enable de-ghosting | +| `PUR_05KR` | The 0.5k Ohm resistor used during blanking period (t_NOL) | +| `PUR_3KR` | The 3k Ohm resistor used at all times | +| `PUR_4KR` | The 4k Ohm resistor used at all times | +| `PUR_8KR` | The 8k Ohm resistor used at all times | +| `PUR_16KR` | The 16k Ohm resistor used at all times | +| `PUR_32KR` | The 32k Ohm resistor used during blanking period (t_NOL) | +  Here is an example using 2 drivers.  ```c @@ -141,7 +159,7 @@ Where `X_Y` is the location of the LED in the matrix defined by [the datasheet](  There is basic support for addressable RGB matrix lighting with the I2C IS31FL3737 RGB controller. To enable it, add this to your `rules.mk`: -```makefile +```make  RGB_MATRIX_ENABLE = yes  RGB_MATRIX_DRIVER = IS31FL3737  ``` @@ -153,11 +171,25 @@ Configure the hardware via your `config.h`:  |----------|-------------|---------|  | `ISSI_TIMEOUT` | (Optional) How long to wait for i2c messages, in milliseconds | 100 |  | `ISSI_PERSISTENCE` | (Optional) Retry failed messages this many times | 0 | +| `ISSI_SWPULLUP` | (Optional) Set the value of the SWx lines on-chip de-ghosting resistors | PUR_0R (Disabled) | +| `ISSI_CSPULLUP` | (Optional) Set the value of the CSx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |  | `DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |  | `DRIVER_LED_TOTAL` | (Required) How many RGB lights are present across all drivers | |  | `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | |  | `DRIVER_ADDR_2` | (Optional) Address for the second RGB driver | | +The IS31FL3737 IC's have on-chip resistors that can be enabled to allow for de-ghosting of the RGB matrix. By default these resistors are not enabled (`ISSI_SWPULLUP`/`ISSI_CSPULLUP` are given the value of`PUR_0R`), the values that can be set to enable de-ghosting are as follows: + +| `ISSI_SWPULLUP/ISSI_CSPULLUP` | Description | +|----------------------|-------------| +| `PUR_0R` | (default) Do not use the on-chip resistors/enable de-ghosting | +| `PUR_05KR` | The 0.5k Ohm resistor used during blanking period (t_NOL) | +| `PUR_1KR` | The 1k Ohm resistor used during blanking period (t_NOL) | +| `PUR_2KR` | The 2k Ohm resistor used during blanking period (t_NOL) | +| `PUR_4KR` | The 4k Ohm resistor used during blanking period (t_NOL) | +| `PUR_8KR` | The 8k Ohm resistor during blanking period (t_NOL) | +| `PUR_16KR` | The 16k Ohm resistor during blanking period (t_NOL) | +| `PUR_32KR` | The 32k Ohm resistor used during blanking period (t_NOL) |  Here is an example using 2 drivers. @@ -181,7 +213,7 @@ Here is an example using 2 drivers.  ```  !> Note the parentheses, this is so when `DRIVER_LED_TOTAL` is used in code and expanded, the values are added together before any additional math is applied to them. As an example, `rand() % (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)` will give very different results than `rand() % DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL`. -Currently only 2 drivers are supported, but it would be trivial to support all 4 combinations.  +Currently only 2 drivers are supported, but it would be trivial to support all 4 combinations.  Define these arrays listing all the LEDs in your `<keyboard>.c`: @@ -206,7 +238,7 @@ Where `X_Y` is the location of the LED in the matrix defined by [the datasheet](  There is basic support for addressable RGB matrix lighting with a WS2811/WS2812{a,b,c} addressable LED strand. To enable it, add this to your `rules.mk`: -```makefile +```make  RGB_MATRIX_ENABLE = yes  RGB_MATRIX_DRIVER = WS2812  ``` @@ -226,7 +258,7 @@ Configure the hardware via your `config.h`:  There is basic support for APA102 based addressable LED strands. To enable it, add this to your `rules.mk`: -```makefile +```make  RGB_MATRIX_ENABLE = yes  RGB_MATRIX_DRIVER = APA102  ``` @@ -246,7 +278,7 @@ Configure the hardware via your `config.h`:  ### AW20216 :id=aw20216  There is basic support for addressable RGB matrix lighting with the SPI AW20216 RGB controller. To enable it, add this to your `rules.mk`: -```makefile +```make  RGB_MATRIX_ENABLE = yes  RGB_MATRIX_DRIVER = AW20216  ``` @@ -340,7 +372,7 @@ x = 224 / (NUMBER_OF_COLS - 1) * COL_POSITION  y =  64 / (NUMBER_OF_ROWS - 1) * ROW_POSITION  ``` -Where NUMBER_OF_COLS, NUMBER_OF_ROWS, COL_POSITION, & ROW_POSITION are all based on the physical layout of your keyboard, not the electrical layout.  +Where NUMBER_OF_COLS, NUMBER_OF_ROWS, COL_POSITION, & ROW_POSITION are all based on the physical layout of your keyboard, not the electrical layout.  As mentioned earlier, the center of the keyboard by default is expected to be `{ 112, 32 }`, but this can be changed if you want to more accurately calculate the LED's physical `{ x, y }` positions. Keyboard designers can implement `#define RGB_MATRIX_CENTER { 112, 32 }` in their config.h file with the new center point of the keyboard, or where they want it to be allowing more possibilities for the `{ x, y }` values. Do note that the maximum value for x or y is 255, and the recommended maximum is 224 as this gives animations runoff room before they reset. @@ -383,7 +415,7 @@ All RGB keycodes are currently shared with the RGBLIGHT system:  * `RGB_MODE_*` keycodes will generally work, but not all of the modes are currently mapped to the correct effects for the RGB Matrix system. -`RGB_MODE_PLAIN`, `RGB_MODE_BREATHE`, `RGB_MODE_RAINBOW`, and `RGB_MATRIX_SWIRL` are the only ones that are mapped properly. The rest don't have a direct equivalent, and are not mapped.  +`RGB_MODE_PLAIN`, `RGB_MODE_BREATHE`, `RGB_MODE_RAINBOW`, and `RGB_MATRIX_SWIRL` are the only ones that are mapped properly. The rest don't have a direct equivalent, and are not mapped.  !> By default, if you have both the [RGB Light](feature_rgblight.md) and the RGB Matrix feature enabled, these keycodes will work for both features, at the same time. You can disable the keycode functionality by defining the `*_DISABLE_KEYCODES` option for the specific feature. @@ -420,7 +452,9 @@ enum rgb_matrix_effects {      RGB_MATRIX_JELLYBEAN_RAINDROPS, // Randomly changes a single key's hue and saturation      RGB_MATRIX_HUE_BREATHING,       // Hue shifts up a slight ammount at the same time, then shifts back      RGB_MATRIX_HUE_PENDULUM,        // Hue shifts up a slight ammount in a wave to the right, then back to the left -    RGB_MATRIX_HUE_WAVE,            // Hue shifts up a slight ammount and then back down in a wave to the right  +    RGB_MATRIX_HUE_WAVE,            // Hue shifts up a slight ammount and then back down in a wave to the right +    RGB_MATRIX_FRACTAL,             // Single hue fractal filled keys pulsing horizontally out to edges +    RGB_MATRIX_PIXEL_RAIN,          // Randomly light keys with random hues  #if define(RGB_MATRIX_FRAMEBUFFER_EFFECTS)      RGB_MATRIX_TYPING_HEATMAP,      // How hot is your WPM!      RGB_MATRIX_DIGITAL_RAIN,        // That famous computer simulation @@ -473,7 +507,9 @@ You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `con  |`#define DISABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS`       |Disables `RGB_MATRIX_JELLYBEAN_RAINDROPS`      |  |`#define DISABLE_RGB_MATRIX_HUE_BREATHING`             |Disables `RGB_MATRIX_HUE_BREATHING`            |  |`#define DISABLE_RGB_MATRIX_HUE_PENDULUM`              |Disables `RGB_MATRIX_HUE_PENDULUM`             | -|`#define DISABLE_RGB_MATRIX_HUE_WAVE `                 |Disables `RGB_MATRIX_HUE_WAVE `                | +|`#define DISABLE_RGB_MATRIX_HUE_WAVE`                  |Disables `RGB_MATRIX_HUE_WAVE`                 | +|`#define DISABLE_RGB_MATRIX_FRACTAL`                   |Disables `RGB_MATRIX_FRACTAL`                  | +|`#define DISABLE_RGB_MATRIX_PIXEL_RAIN `               |Disables `RGB_MATRIX_PIXEL_RAIN `              |  |`#define DISABLE_RGB_MATRIX_TYPING_HEATMAP`            |Disables `RGB_MATRIX_TYPING_HEATMAP`           |  |`#define DISABLE_RGB_MATRIX_DIGITAL_RAIN`              |Disables `RGB_MATRIX_DIGITAL_RAIN`             |  |`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE_SIMPLE`     |Disables `RGB_MATRIX_SOLID_REACTIVE_SIMPLE`    | @@ -537,7 +573,7 @@ static bool my_cool_effect(effect_params_t* params) {    for (uint8_t i = led_min; i < led_max; i++) {      rgb_matrix_set_color(i, 0xff, 0xff, 0x00);    } -  return led_max < DRIVER_LED_TOTAL; +  return rgb_matrix_check_finished_leds(led_max);  }  // e.g: A more complex effect, relying on external methods and state, with @@ -551,8 +587,7 @@ static bool my_cool_effect2_complex_run(effect_params_t* params) {    for (uint8_t i = led_min; i < led_max; i++) {      rgb_matrix_set_color(i, 0xff, some_global_state++, 0xff);    } - -  return led_max < DRIVER_LED_TOTAL; +  return rgb_matrix_check_finished_leds(led_max);  }  static bool my_cool_effect2(effect_params_t* params) {    if (params->init) my_cool_effect2_complex_init(params); @@ -694,7 +729,7 @@ Where `28` is an unused index from `eeconfig.h`.  ### Indicators :id=indicators -If you want to set custom indicators, such as an LED for Caps Lock, or layer indication, you can use the `rgb_matrix_indicators_kb` or `rgb_matrix_indicators_user` function for that:  +If you want to set custom indicators, such as an LED for Caps Lock, or layer indication, you can use the `rgb_matrix_indicators_kb` or `rgb_matrix_indicators_user` function for that:  ```c  void rgb_matrix_indicators_kb(void) {      rgb_matrix_set_color(index, red, green, blue); @@ -749,18 +784,18 @@ This example sets the modifiers to be a specific color based on the layer state.  ```c  void rgb_matrix_indicators_advanced_user(uint8_t led_min, uint8_t led_max) {      HSV hsv = {0, 255, 255}; -     +      if (layer_state_is(layer_state, 2)) {          hsv = {130, 255, 255};      } else {          hsv = {30, 255, 255};      } -     +      if (hsv.v > rgb_matrix_get_val()) {          hsv.v = rgb_matrix_get_val();      }      RGB rgb = hsv_to_rgb(hsv); -     +      for (uint8_t i = led_min; i <= led_max; i++) {          if (HAS_FLAGS(g_led_config.flags[i], 0x01)) { // 0x01 == LED_FLAG_MODIFIER              rgb_matrix_set_color(i, rgb.r, rgb.g, rgb.b); @@ -769,7 +804,7 @@ void rgb_matrix_indicators_advanced_user(uint8_t led_min, uint8_t led_max) {  }  ``` -If you want to indicate a Host LED status (caps lock, num lock, etc), you can use something like this to light up the caps lock key:  +If you want to indicate a Host LED status (caps lock, num lock, etc), you can use something like this to light up the caps lock key:  ```c  void rgb_matrix_indicators_advanced_user(uint8_t led_min, uint8_t led_max) { | 
